Skip to content
Austin project guide

Cabinet Painting in Austin Clarify the work first.

Plan cabinet painting with the preparation, doors, drawers, and finish your project needs.

See the complete painting workflow

Service scope guide

Direct answer

Count every component and identify the existing finish.

Cabinet refinishing should distinguish doors, drawer fronts, boxes, panels, islands, interiors, and hardware. The existing finish and substrate determine the cleaning, repair, bonding, application, and curing plan.

How this review starts

A complete component count and detailed photos can begin the review. Unknown finishes, coating failure, damage, or a spray setup may require an on-site assessment.

01 · What to prepare

Answer what you can see.

Document only what you can observe safely. Do not scrape, sand, remove, or disturb a suspect coating or material to answer a question or take a photo.

  • Component count

    How many doors, drawer fronts, boxes, end panels, islands, shelves, trim pieces, and glass inserts are included?

  • Existing finish

    Is the finish paint, stain, clear coat, laminate, thermofoil, factory coating, bare wood, or unknown?

  • Condition

    Where are grease, peeling, chips, water damage, open joints, failed caulk, or prior repairs?

  • Hardware

    Will hinges, pulls, knobs, bumpers, slides, or other hardware be reused, replaced, or relocated?

  • Finish method

    Where will doors and drawers be finished, and what appearance and sheen are expected?

  • Use and access

    How will the kitchen or room be used during removal, preparation, drying, and curing?

02 · Professional confirmation

Conditions to verify before approval.

  • Substrate, existing finish, adhesion, grease removal, damage, and whether each surface is suitable for refinishing.
  • Door and drawer labeling, hardware handling, repairs, sanding, cleaning, and bonding primer.
  • Application location and method, containment, ventilation, finish system, and curing conditions.
  • Reinstallation, alignment, bumper or hardware work, and the point when normal use can resume.

03 · Written scope

Lines that make the work clear.

  • Every door, drawer front, box, panel, island, shelf, trim piece, interior, and excluded component.
  • Removal, labeling, repair, cleaning, sanding, primer, and treatment of the existing finish.
  • Coating system, color, sheen, application method, work location, containment, and curing plan.
  • Hardware responsibility, reinstallation, alignment, cleanup, walkthrough, and change approval.

Before comparing proposals

Make sure each proposal answers the same job.

  • Doors, drawers, boxes, panels, islands, shelves, trim, and interiors use the same count.
  • Existing finish, repairs, degreasing, sanding, and primer assumptions match.
  • Application method, work location, containment, drying, and curing match.
  • Hardware, labeling, storage, reinstallation, alignment, and cleanup are assigned.

How your project works

From your idea to an agreed plan.

Describe the work, review an estimate, and choose a local pro where matching is available. Your contractor checks the project before you both agree to the work and price.

  1. 01 · Describe

    Tell us what you need.

    Add your address, photos, measurements, and preferred timing.

  2. 02 · Estimate

    See an estimate or get a closer look.

    Supported work with enough detail can receive a real-time estimate.

  3. 03 · Choose a pro

    Find the right fit for your project.

    Where matching is available, compare local pros and choose whom to hire.

  4. 04 · Agree and begin

    Keep the agreed plan in one place.

    You and your contractor approve the work, price, and terms before the job begins.

When an on-site review is needed

Some details need a visit.

A professional checks conditions that photos or measurements cannot safely confirm. The review helps define the work; it does not guarantee acceptance or a particular price. Unknown work must be reviewed before it is priced.

No submitted estimate becomes accepted work until a professional reviews the project and both sides agree to the scope, price, and terms.

Accuracy references

Official guidance supports the permit and lead-safe notes used on this page.

Continue with the details

Build the project record in Completa.

Use the app for the service-specific questions, photos, written scope, approvals, milestones, and project history.

Continue in Completa

Products and materials

Confirm the exact product and who supplies it.

These products are linked to the service scope. The professional still confirms compatibility, finish, quantity, availability, and manufacturer instructions.

  • B-I-N Shellac-Based White Interior Primer and Sealer

    Cabinet primer · sold by the gallon

Common questions

Can every cabinet finish be painted the same way?
No. Wood, factory coatings, laminate, thermofoil, clear finishes, and prior paint can require different preparation and may not all be suitable for the same refinishing system.
Are cabinet interiors normally included?
Only when named. Interiors, shelves, boxes, door backs, drawer fronts, and trim should be listed separately so the scope does not depend on an assumption.
When can cabinets return to normal use?
Drying, reinstallation, and full curing are different stages. The professional should provide handling and normal-use guidance for the specified coating and site conditions.