Skip to content
← All articlesPermits & Rules · 10 min read
By Steve — Co-founder and CEO, Completa
Published 2026-11-16 · Updated 2026-11-16

Mold after a leak in Texas: what you can clean yourself and when a pro must be licensed

You can clean mold in your own Texas home without a license. When hired mold testing and removal need a TDLR license, what a licensed job includes, and safe steps.

Texas law lets you clean up mold in a home you own, on a property with fewer than 10 units, without a license and whatever its size. Most other people need a TDLR license: the law requires a mold assessment license to assess mold, and a mold remediation license to remove mold covering 25 contiguous square feet or more, unless an exemption below applies. A licensed job comes with a written plan from a separate assessor and a certificate when the work is done. Being allowed to do it yourself is not the same as being advised to: EPA says that in most cases you can handle a patch under about 10 square feet yourself, and for more it points to its professional cleanup guide.

This guide covers the Texas mold law, what a licensed job includes and federal cleanup advice, each from the agency's own text.

NumberMeansSource
24–48 hoursDrying windowEPA
About 10 sq ftDIY guidelineEPA
25 contiguous sq ftLicense lineTexas law
10 daysCertificate dueTexas law

Of the two square-foot figures, only the 25-square-foot line is law. EPA's 10-square-foot figure is advice about who should do the cleanup; it carries no license requirement.

What Texas counts as mold work

The Texas Department of Licensing and Regulation (TDLR) licenses mold assessors and remediators under Chapter 1958 of the Occupations Code and its rules in 16 Texas Administrative Code Chapter 78. The program moved to TDLR from the Department of State Health Services on November 1, 2017.

  • Mold assessment is an inspection, investigation or survey of a home for mold; writing a mold management plan or remediation protocol; or collecting or analyzing a mold sample.
  • Mold remediation is removing, cleaning, sanitizing, demolishing or otherwise treating mold or mold-contaminated material, including preventive work.

The law covers mold work that affects indoor air quality. It does not cover routine cleaning, or a plumber, HVAC or electrical technician diagnosing and repairing a system, unless the work is done for the purpose of mold assessment or remediation. TDLR's FAQ says a real estate inspector can note visible mold without a mold license but needs one to collect air or spore samples.

When no license is needed

Section 1958.102 of the law lists these exemptions:

  • Owners of homes with fewer than 10 units. An owner, or the owner's managing agent or employee, can assess and remediate mold on a residential property the owner owns with fewer than 10 dwelling units. TDLR's rules say this applies regardless of how much area the mold covers. It does not apply to an agent or employee who is in the business of mold work for the public.
  • Small remediation jobs, for anyone. No license is needed to remediate mold when the contamination for the project covers less than 25 contiguous square feet. The law writes this exemption for remediation only, while TDLR's summary sheet lists projects under 25 square feet as exempt without that limit, so ask TDLR before you hire someone unlicensed to test a small area.
  • Tenants and owners of other property. An owner or tenant can do mold work on property they own or lease, but the remediation exemption ends at 25 contiguous square feet.
  • Builders. A builder can handle mold in a one- or two-family home it built or added to, while doing that construction, or repair work on it, unless it is in the business of mold work for the public. TDLR's rules apply this exemption regardless of the mold's size, and its FAQ says it covers work under the builder's warranty, including by its subcontractors.

If someone relying on an under-25-square-foot exemption finds more mold and the total reaches 25 contiguous square feet, TDLR's rules require them to stop, set up emergency containment if needed, and tell the person who asked for the work that the exemption is lost. The rest of the remediation, and the check afterward, then need licensed pros.

When the pro must be licensed

Under §1958.101 of the law, anyone outside those exemptions needs a TDLR license:

  • Assessment, including inspecting for mold, taking samples or writing a remediation protocol, needs a mold assessment license.
  • Remediation of 25 contiguous square feet or more needs a mold remediation license.

TDLR's FAQ says that if you hire a licensed remediator, the full rules apply even to a job under 25 contiguous square feet, including a work plan that follows a licensed consultant's protocol, though the remediator does not have to notify TDLR of a job that small.

The assessor and the remediator must be independent

Texas law bars a license holder from performing both mold assessment and mold remediation on the same project. No one may own an interest in both the assessment company and the remediation company on the same project. The only exception is a license holder employed by a school district working on that district's project.

What a licensed job includes

Texas law and TDLR's rules require these steps:

  1. An information sheet first. Before any mold-related activity begins, a licensed assessor or remediator must give the client, and the property owner if different, TDLR's Consumer Mold Information Sheet.
  2. A protocol from the assessor. A licensed mold assessment consultant writes a mold remediation protocol for the project and gives it to the client at least one calendar day before remediation begins. It must list the rooms or areas, how much material will be cleaned or removed, the methods, the protective equipment, the containment and the clearance criteria. The statute separately requires the assessor to give the client a written work analysis, with much the same contents, before remediation begins. For 25 contiguous square feet or more, the protocol must call for containment that keeps mold from spreading to the rest of the building, unless only licensed or registered workers occupy the building during the job.
  3. A work plan from the remediator. The remediator gives the client written instructions for the job before remediation begins and keeps a copy at the job site.
  4. Notice to TDLR. The remediator notifies TDLR at least five days before remediation starts. In an emergency, when delay after water damage would increase mold contamination, notice is due by the next business day.
  5. A clearance check. Before a project counts as successful, a licensed mold assessment consultant inspects the finished work and gives you a passed clearance report. If it fails, more remediation follows.
  6. Photos and a certificate within 10 days. Within ten days after the project ends, the remediation contractor or company must give the property owner before-and-after photos and a Certificate of Mold Damage Remediation on a Texas Department of Insurance form. The assessment consultant and the remediation contractor both sign it. The consultant states that the mold identified for the project was remediated as outlined in the protocol, and says whether the underlying cause was remediated so that it is reasonably certain the mold will not return from that cause.

If you sell the home, the law requires you to give the buyer a copy of each certificate issued for the property in the five years before the sale.

When to call a pro even if the law lets you do it

EPA and CDC advise extra care, or a professional, in these cases:

  • More than about 10 square feet, or a lot of water damage. EPA says that under about 10 square feet, roughly a 3-by-3-foot patch, in most cases you can handle the job yourself. Above that, it points to its guide Mold Remediation in Schools and Commercial Buildings, which it says also applies to other buildings.
  • Sewage or other contaminated water. EPA says to call a professional who has experience with buildings damaged by contaminated water.
  • A heating and cooling system that may be moldy. EPA says not to run the system if you know or suspect it is contaminated, because it could spread mold throughout the building, and to read its guide on air duct cleaning before doing anything else.
  • Hidden mold. Mold can grow on the back of drywall, under carpet pads and inside ductwork. EPA warns that disturbing it, such as pulling off wallpaper, can release a large amount of spores, and suggests an experienced professional.
  • Health concerns. CDC says people with asthma or mold allergies may have severe reactions, and immune-compromised people and people with chronic lung disease may get lung infections from mold. EPA advises asking a health professional before you start cleanup.

Cleaning it yourself: a step checklist

  1. Stop the water. Shut off the source and fix the leak. If water reached outlets, cords or the electrical panel, stay out of the wet area until an electrician or your utility has shut off the power. If you may file a claim, read the insurance section below before you throw anything out.
  2. Dry within 24–48 hours. EPA says that if wet materials are dried within 24 to 48 hours of a leak, in most cases mold will not grow. The Texas Department of Insurance notes mold can start growing within a day. Pull up wet carpets and rugs.
  3. Measure the mold. 25 square feet is a 5-by-5-foot patch. If you are near EPA's 10-square-foot guideline or the 25-square-foot line, reread the sections above.
  4. Gear up. EPA's list: an N-95 respirator that fits properly, long gloves and goggles without ventilation holes. Don't touch mold with bare hands.
  5. Remove porous materials; clean hard ones. TDLR says mold is hard to clean from drywall, carpet, fleecy furnishings and insulation, and those materials should be removed and discarded. Hard surfaces such as concrete, metal, glass, tile and solid wood can be cleaned; EPA says to scrub them with detergent and water and dry them completely. After a flood, FEMA says to remove all drywall and insulation that touched floodwater.
  6. Don't count on bleach. TDLR says bleach on drywall, without removing the mold source, is not an effective, permanent fix, and EPA does not recommend biocides as a routine step. Never mix bleach with ammonia.
  7. Don't paint over mold. EPA says to clean and dry the surface first; paint over mold is likely to peel.
  8. Skip the test kit, usually. EPA says sampling is usually unnecessary when mold is visible, CDC does not recommend mold testing, and TDLR notes there are no national or state standards for a "safe" level of mold.
  9. Check the result. EPA's test: the water problem is fixed, no visible mold or moldy odor remains, and a return visit shortly after shows no new water damage or mold.

Insurance and the mold certificate

The Texas Department of Insurance (TDI) says most homeowner and renters policies cover sudden and accidental water damage, such as a burst pipe, toilet overflow or broken washer hose, and mold that develops on a damaged item would be covered. Most don't cover gradual leaks or seepage, including the mold they cause, and home policies don't cover floods, which need a separate flood policy. Most also don't include mold cleanup and testing after a damaged item is removed, though an insurer may let you add that coverage for cleanup caused by a covered loss. Coverage depends on your own policy, so ask your agent or insurer.

TDI's claim tips:

  • Tell your insurance company as soon as possible. Hidden water damage usually must be reported within days after you first see it.
  • Photograph or video the damage before repairs, and don't throw away damaged items until the adjuster has seen them.
  • Make temporary repairs and keep receipts, but no permanent repairs until the insurer sees the damage.
  • For a mold claim, make sure the mold professional has a state license. You'll need an inspection showing the mold was removed and its cause fixed.

Texas Insurance Code §544.303 bars a residential property insurer from making an underwriting decision based on previous mold damage or a mold claim, for a home otherwise eligible for coverage, once mold remediation has been done and either a certificate establishes with reasonable certainty that the underlying cause was remediated, or an independent assessor or adjuster inspected the home and found no evidence of mold damage. The rule does not cover surplus lines insurers, the Texas Windstorm Insurance Association or the Texas FAIR Plan.

If you did the work yourself, or a builder's unlicensed crew did it under the builder exemption, you can't get the remediation certificate; TDLR says only a licensed remediator can give one. Instead, a licensed mold assessment consultant or an insurance adjuster can inspect the home and sign the "no mold damage was found" section of the same TDI certificate form. The form tells owners to keep the certificate and give a copy to their insurance agent or company.

If you rent

Under the tenant exemption above, you can clean mold in a rental without a license only below 25 contiguous square feet. TDLR does not inspect homes for mold and cannot make a landlord clean it up. Austin's Code Compliance division doesn't test for mold either, but it may act on causes such as leaks under the city's minimum standards. If your landlord hasn't fixed the problem, call Austin 3-1-1.

Check the license before work starts

TDLR's License Search lists active licenses by license type, license number or name. Mold license types include Mold Assessment Consultant, Mold Assessment Company, Mold Remediation Contractor and Mold Remediation Company. TDLR's consumer sheet says a licensed individual must carry a current TDLR license certificate showing the license number. Austin Code says it does not regulate mold inspectors; the state licenses and regulates assessors and remediators. You can report unlicensed mold work, or a complaint about a licensee, to TDLR within two years of the event.

This guide is practical information, not legal or medical advice. It quotes the law and rules as published on November 16, 2026. Texas amended the mold law in 2025 through Senate Bill 1255, and TDLR says its current rules stay in effect until it adopts new ones. For your situation, ask TDLR's mold program at mold.inspections@tdlr.texas.gov or 800-803-9202, and ask a health professional about health concerns.

Where Completa fits

Completa connects homeowners with local pros for the repairs around a leak, such as plumbing. If the pro finds mold, measure it against the 25-contiguous-square-foot line above, and ask TDLR if you're unsure whether you need a licensed assessor and remediator.

Frequently asked questions

Can I remove mold myself in Texas?

Yes, in your own house. Texas law lets the owner of a residential property with fewer than 10 dwelling units do mold assessment and remediation without a license, and TDLR's rules say that applies whatever the size of the mold area. EPA says that in most cases you can handle a patch under about 10 square feet yourself; for more, it points to its professional cleanup guide.

When does mold removal need a licensed remediator in Texas?

Under Texas law, removing mold that covers 25 contiguous square feet or more needs a TDLR-licensed remediator, unless the owner of a home with fewer than 10 units, or the owner's own employee or managing agent, does it. Tenants and owners of other property are exempt only below 25 contiguous square feet. A hired mold assessment, such as testing or writing a protocol, needs a TDLR mold assessment license unless an exemption applies; ask TDLR to confirm for your job.

Can the same company test for mold and remove it in Texas?

Not on the same project. Texas law bars one license holder from doing both, and bars anyone from owning an interest in both companies on one project, except a license holder employed by a school district on that district's project.

Do I have to give a mold remediation certificate to a buyer in Texas?

Yes, if any were issued. Texas law requires a seller to give the buyer a copy of each certificate of mold remediation issued for the property in the five years before the sale.